56 lines
2.4 KiB
PowerShell
56 lines
2.4 KiB
PowerShell
|
# Builds two Windows EXEs for V2X2MAP:
|
||
|
|
# dist\its-g5-bridge.exe -- bridge only, starts directly (reads config\v2x2map.cfg)
|
||
|
|
# dist\its-g5-setup.exe -- setup wizard + firmware flash
|
||
|
|
#
|
||
|
|
# Run from V2X2MAP\bridge:
|
||
|
|
# .\build_exe.ps1
|
||
|
|
|
||
|
|
$ErrorActionPreference = 'Continue'
|
||
|
|
|
||
|
|
# Refresh bundled firmware bins from the latest build/ if it exists.
|
||
|
|
$buildDir = Resolve-Path "..\firmware\build" -ErrorAction SilentlyContinue
|
||
|
|
if ($buildDir) {
|
||
|
|
Copy-Item "$buildDir\bootloader\bootloader.bin" ".\firmware\bootloader.bin" -Force
|
||
|
|
Copy-Item "$buildDir\partition_table\partition-table.bin" ".\firmware\partition-table.bin" -Force
|
||
|
|
Copy-Item "$buildDir\ota_data_initial.bin" ".\firmware\ota_data_initial.bin" -Force
|
||
|
|
Copy-Item "$buildDir\its-g5-receiver-firmware.bin" ".\firmware\firmware.bin" -Force
|
||
|
|
Write-Host "Firmware-Bins aktualisiert aus $buildDir"
|
||
|
|
} else {
|
||
|
|
Write-Host "Kein ..\firmware\build\ gefunden -- bestehende firmware\*.bin werden verwendet."
|
||
|
|
}
|
||
|
|
|
||
|
|
# Ensure required packages are available.
|
||
|
|
python -m pip install --quiet -r requirements.txt pyinstaller esptool pillow
|
||
|
|
|
||
|
|
# Generate icons
|
||
|
|
Write-Host ""
|
||
|
|
Write-Host "=== Generiere Icons ==="
|
||
|
|
python make_icons.py
|
||
|
|
if ($LASTEXITCODE -ne 0) { Write-Warning "Icon-Generierung fehlgeschlagen -- baue ohne Icons weiter." }
|
||
|
|
|
||
|
|
Write-Host ""
|
||
|
|
Write-Host "=== Baue its-g5-bridge.exe (Bridge ohne Wizard) ==="
|
||
|
|
python -m PyInstaller --noconfirm its-g5-bridge.spec
|
||
|
|
if ($LASTEXITCODE -ne 0) { Write-Error "Bridge-Build fehlgeschlagen."; exit 1 }
|
||
|
|
|
||
|
|
Write-Host ""
|
||
|
|
Write-Host "=== Baue its-g5-setup.exe (Setup-Wizard und Flash) ==="
|
||
|
|
python -m PyInstaller --noconfirm its-g5-setup.spec
|
||
|
|
if ($LASTEXITCODE -ne 0) { Write-Error "Setup-Build fehlgeschlagen."; exit 1 }
|
||
|
|
|
||
|
|
$bridge = (Get-Item "dist\its-g5-bridge.exe").Length / 1MB
|
||
|
|
$setup = (Get-Item "dist\its-g5-setup.exe").Length / 1MB
|
||
|
|
Write-Host ""
|
||
|
|
Write-Host "Fertig:"
|
||
|
|
Write-Host (" dist\its-g5-bridge.exe {0:N1} MB -- Doppelklick zum Starten" -f $bridge)
|
||
|
|
Write-Host (" dist\its-g5-setup.exe {0:N1} MB -- Einrichten und Flashen" -f $setup)
|
||
|
|
Write-Host ""
|
||
|
|
Write-Host "Ordnerstruktur nach dem ersten Start:"
|
||
|
|
Write-Host " dist\"
|
||
|
|
Write-Host " its-g5-bridge.exe"
|
||
|
|
Write-Host " its-g5-setup.exe"
|
||
|
|
Write-Host " config\"
|
||
|
|
Write-Host " v2x2map.cfg (von Setup geschrieben)"
|
||
|
|
Write-Host " recordings\"
|
||
|
|
Write-Host " its5_*.pcap (PCAP-Aufnahmen)"
|