Sign ITS messages on the ESP32-C5 with vanetza-idf, over USB or BLE

obu-firmware is now a port of the colleague's standalone VRU station
(microbu-esp32c5/firmware, kept beside this repository and gitignored): the
vanetza-idf C-ITS stack with the TS 103 097 security entity, credentials in
NVS, the station-link v1 protocol over the native USB port (frame type 0x10
in the existing 0xAA55 framing) and over a BLE GATT peripheral, and its
ITS-G5 radio adapter. The phone still builds CAM and VAM; the board adds
GeoNetworking/BTP and signs with the provisioned authorization ticket. The
private key never leaves the board. Builds with ESP-IDF 6.0.2 only, which
vanetza-idf pins for the radio's private driver ABI. The previous C firmware
stays on disk unbuilt; a full-flash backup of the bench board is kept in
firmware-backups/ (gitignored).

Changed against the colleague's firmware, marked MicrOBU: in the sources:
- Reception unchanged for the app. vanetza-idf drops what it cannot verify
  (unsigned traffic, every RSU), so each captured frame also goes through the
  previous gn_unwrap.c and reaches the phone as link opcode V2X_RX (0x85),
  whose body is the old SERIAL_MSG_V2X_RX payload.
- Unsigned transmission still possible, with the previous geonet.c header;
  the phone chooses per message.
- Console on UART0 (CH343 port); the native USB port carries only link frames.
- BLE advertising pauses while the USB link is in use: BLE and ITS-G5 share
  one RF front end.
- NVS 80 KB (app at 0x20000). At 24 KB, with Wi-Fi settings the previous
  firmware left behind, the BLE bond could not be stored and the phone had to
  pair on every connection.
- Bench fixes: the radio queue is drained before the first PoTi (no RX and
  ~177 queue drops before); the station loop waited pdMS_TO_TICKS(5) = 0
  ticks at 100 Hz and starved the idle task; the 2.4 KB RX capture buffer is
  off the Wi-Fi task stack; BLE notifications longer than the MTU are dropped
  instead of cut short, MTU 517; serial writes are skipped with no USB host.
- Manual country policy and TX-power read-back from the previous radio setup;
  logs for BLE encryption changes and the number of stored bonds.

Verified on the bench board (COM3) with the phone over USB and BLE: CAM and
VAM, signed and unsigned, go out; reception of the sim car and the RSU's
CAM/SPATEM/MAPEM continues; the board survives app restarts and reconnects.
See docs/06-signed-its-vam-ble.md.

obu-firmware/dependencies.lock

@@ -0,0 +1,21 @@
+dependencies:
+  espressif/esp-boost:
+    component_hash: 45cfa63ade2ad7c489203ab2ddf3f33be50ec9cab752b6eb17a79f06aee8f8f0
+    dependencies:
+    - name: idf
+      require: private
+      version: '>=5.3'
+    source:
+      registry_url: https://components.espressif.com/
+      type: service
+    version: 0.4.1
+  idf:
+    source:
+      type: idf
+    version: 6.0.2
+direct_dependencies:
+- espressif/esp-boost
+- idf
+manifest_hash: 3fca1283d556ade5b08c63857e23cb3b08582f1d1c24bb7c1d5e374f438415d7
+target: esp32c5
+version: 3.0.0