obu-firmware is now a port of the colleague's standalone VRU station
(microbu-esp32c5/firmware, kept beside this repository and gitignored): the
vanetza-idf C-ITS stack with the TS 103 097 security entity, credentials in
NVS, the station-link v1 protocol over the native USB port (frame type 0x10
in the existing 0xAA55 framing) and over a BLE GATT peripheral, and its
ITS-G5 radio adapter. The phone still builds CAM and VAM; the board adds
GeoNetworking/BTP and signs with the provisioned authorization ticket. The
private key never leaves the board. Builds with ESP-IDF 6.0.2 only, which
vanetza-idf pins for the radio's private driver ABI. The previous C firmware
stays on disk unbuilt; a full-flash backup of the bench board is kept in
firmware-backups/ (gitignored).
Changed against the colleague's firmware, marked MicrOBU: in the sources:
- Reception unchanged for the app. vanetza-idf drops what it cannot verify
(unsigned traffic, every RSU), so each captured frame also goes through the
previous gn_unwrap.c and reaches the phone as link opcode V2X_RX (0x85),
whose body is the old SERIAL_MSG_V2X_RX payload.
- Unsigned transmission still possible, with the previous geonet.c header;
the phone chooses per message.
- Console on UART0 (CH343 port); the native USB port carries only link frames.
- BLE advertising pauses while the USB link is in use: BLE and ITS-G5 share
one RF front end.
- NVS 80 KB (app at 0x20000). At 24 KB, with Wi-Fi settings the previous
firmware left behind, the BLE bond could not be stored and the phone had to
pair on every connection.
- Bench fixes: the radio queue is drained before the first PoTi (no RX and
~177 queue drops before); the station loop waited pdMS_TO_TICKS(5) = 0
ticks at 100 Hz and starved the idle task; the 2.4 KB RX capture buffer is
off the Wi-Fi task stack; BLE notifications longer than the MTU are dropped
instead of cut short, MTU 517; serial writes are skipped with no USB host.
- Manual country policy and TX-power read-back from the previous radio setup;
logs for BLE encryption changes and the number of stored bonds.
Verified on the bench board (COM3) with the phone over USB and BLE: CAM and
VAM, signed and unsigned, go out; reception of the sim car and the RSU's
CAM/SPATEM/MAPEM continues; the board survives app restarts and reconnects.
See docs/06-signed-its-vam-ble.md.
Enumeration:
- Merge the library's stock probe table instead of replacing it, so adding
Espressif 0x303A/0x1001 doesn't drop every other supported device
- Select the ESP32-C5 by VID/PID rather than list position
- Log USB interface descriptors to distinguish CDC data from the JTAG interface
Lifecycle:
- Don't close the shared port in MqttViewModel.onCleared() - the foreground
recording service outlives the ViewModel and would beacon into a dead port
- Handle ACTION_USB_DEVICE_DETACHED so the UI stops reporting a stale link
- Implement the STATUS heartbeat on both sides (1 Hz) plus a phone-side watchdog
- Surface write failures and firmware drop counters on the CAM Pinger card
Protocol:
- Assert DTR/RTS on open (unverified on hardware - see FLASHING.md step 5)
- Raise SERIAL_LINK_MAX_PAYLOAD 160 -> 512 on both sides; real third-party CAMs
exceed 160 and were being silently dropped at the resync branch
- Move the enlarged buffers off task stacks; serialize send_frame with a mutex
Firmware and app must be updated together - a 512/160 mismatch fails silently.
- Firmware: rewrite obu-firmware TX loop to be serial-driven (no on-chip timer), add promiscuous RX + GeoNetworking/BTP unwrap (gn_unwrap.c), add binary UART framing to the phone (serial_link.c/.h). Drop local cam_encode() - CAM is now built on the phone.
- Kotlin: byte-exact UPER CAM encoder/decoder ported from cam.c (BitWriter/BitReader/CamUperCodec), matching SerialFrame codec, real UsbSerialTransport (usb-serial-for-android), CamTransmitLoop (1Hz base rate, event/geofence boost, ESP32-C5-only), wired into CamUseCaseRepository for RX and TripRecordingService for TX.
- Add V2X message retention: persist all CAM (own+remote) to Room while recording, drop otherwise (DB v2 -> v3 migration).
- Add jitpack repo + usb-serial-for-android dependency.
Fixes: UsbSerialTransport now uses SerialInputOutputManager.start()/stop() (this lib version manages its own thread internally) instead of manual Runnable/Thread submission, which didn't compile.
Ashin Walpola